电子类文献中英文翻译---直流发电机(编辑修改稿)

电子类文献中英文翻译---直流发电机(编辑修改稿)内容摘要：

generator output voltage is sensed and pared to a fixed reference voltage deviation from the reference voltage gives an error signal that is fed to a power amplifier. The power amplifier supplies the field excitation current. If the error signal is positive, for example, the output voltage is larger than desired 9 and the amplifier will reduce its current drive. In doing so the error signal will be reduced to zero. TRANSFORMER 1. INTRODUCTION The highvoltage transmission was need for the case electrical power is to be provided at considerable distance from a generating station. At some point this high voltage must be reduced, because ultimately is must supply a load. The transformer makes it possible for various parts of a power system to operate at different voltage levels. In this paper we discuss power transformer principles and applications. 2. TOWWINDING TRANSFORMERS A transformer in its simplest form consists of two stationary coils coupled by a mutual magic flux. The coils are said to be mutually coupled because they link a mon flux. In power applications, laminated steel core transformers (to which this paper is restricted) are used. Transformers are efficient because the rotational losses normally associated with rotating machine are absent, so relatively little power is lost when transforming power from one voltage level to another. Typical efficiencies are in the range 92 to 99%, the higher values applying to the larger power transformers. The current flowing in the coil connected to the ac source is called the primary winding or simply the primary. It sets up the flux φ in the core, which varies periodically both in magnitude and direction. The flux links the second coil, called the secondary winding or simply secondary. The flux is changing。 therefore, it induces a voltage in the secondary by electromagic induction in accordance with Lenz’s law. Thus the primary receives its power from the source while the secondary supplies this power to the load. This action is known as transformer action. 3. TRANSFORMER PRINCIPLES 10 When a sinusoidal voltage Vp is applied to the primary with the secondary opencircuited, there will be no energy transfer. The impressed voltage causes a small current Iθ to flow in the primary winding. This noload current has two functions: (1) it produces the magic flux in the core, which varies sinusoidally between zero and  φm, where φm is the maximum value of the core flux。 and (2) it provides a ponent to account for the hysteresis and eddy current losses in the core. There bined losses are normally referred to as the core losses. The noload current Iθ is usually few percent of the rated fullload current of the transformer (about 2 to 5%). Since at noload the primary winding acts as a large reactance due to the iron core, the noload current will lag the primary voltage by nearly 90186。 . It is readily seen that the current ponent Im= I0sinθ0, called the magizing current, is 90186。 in phase behind the primary voltage VP. It is this ponent that sets up the flux in the core。 φ is therefore in phase with Im. The second ponent, Ie=I0sinθ0, is in phase with the primary voltage. It is the current ponent that supplies the core losses. The phasor sum of these two ponents represents the noload current, or I0 = Im+ Ie It should be noted that the noload current is distortes and nonsinusoidal. This is the result of the nonlinear behavior of the core material. If it is assumed that there are no other losses in the transformer, the induced voltage In the primary, Ep and that in the secondary, Es can be shown. Since the magic flux set up by the primary winding， there will be an induced EMF E in the secondary winding in accordance with Faraday’s law, namely, E=NΔφ/Δt. This same flux also links the primary itself, inducing in it an EMF, Ep. As discussed earlier, the induced voltage must lag the flux by 90186。 , therefore, they are 180186。 out of phase with the applied voltage. Since no current flows in the secondary winding, Es=Vs. The noload primary current I0 is small, a few percent of fullload current. Thus the voltage in the primary is small and Vp is nearly equal to Ep. The primary voltage and the resulting flux are sinusoidal。 thus the induced quantities Ep and Es vary as a sine function. The average value of the induced voltage given by 11 Eavg = turns c h a n g e in flu x in a g iv e n tim eg iv e n tim e which is Faraday’s law applied to a finite time interval. It follows that Eavg = N 21/(2 )mf = 4fNφm which N is the number of turns on the winding. Form ac circuit theory, the effective or rootmeansquare (rms) voltage for a sine wave is times the average voltage。 thus E = Since the same flux links with the primary and secondary windings, the voltage per turn in each winding is the same. Hence Ep = and Es = where Ep and Es are the number of turn on the primary and secondary windings, respectively. The ratio of primary to secondary induced voltage is called the transformation ratio. Denoting this ratio by a, it is seen that a = psEE = psNN Assume that the output power of a transformer equals its input power, not a bad sumption in practice considering the high efficiencies. What we really are saying is that we are dealing with an ideal transformer。 that is, it has no losses. Thus Pm = Pout or VpIp primary PF = VsIs secondary PF where PF is the power factor. For the abovestated assumption it means that the power factor on primary and secondary sides are equal。 therefore VpIp = VsIs from which is obtained psVV = psII ≌ psEE ≌ a 12 It shows that as an approximation the terminal voltage ratio equals the turns ratio. The primary and secondary current, on the other hand, are inversely related to the turns ratio. The turns rat。