driveconvf61系列变频器英文说明书

driveconvf61系列变频器英文说明书内容摘要：

urrent. OL operation starts at 100%. (OL set=100%) Estimated torque is displayed in percentage Remarked 06 Motor speed Motor (synchronous) revolution rpm 07 OL counter OL counter % 08 Line speed Line speed ... 6 Display on LCD 09 10 11 12 13 14 11term check 12term check 0term check Items Input terminal check 1 Input terminal check 2 Output terminal Units bit bit bit Remarked 1 is displayed when terminal block is turned on. For meaning of each bit, se table below. Ditto Ditto 15 ROM Version ROM Version XXXX of ROM software version VF61XXXX is displayed through conversion of alphabetic characters into numeric characters like A=0, B=1 and so forth. 16 17 Special moni Trouble moni For manufacturer’s adjustment Reading error records. Contents of latest five errors and current, voltage, etc. of these errors are displayed. Function mode Press the FUNC key, and current data is displayed as shown below. The internal data of the setting functions may be checked and changed. (See below.) Code number of setting function and contents are displayed. To change a displayed code number of the setting function, press a numeric key (09), function entry key, and up or down arrow key. SP set1, SP set2 and option of sixteen basic data codes 0 to 15 and expanded items of code 16 may be selected with the SET, up and down arrow keys. Set data is displayed. Changing set data (1)Before changing data The numeric keys may be used. To change the set data, press the SET key. * FUNCTION SET * (00)Ref(Set).F [Hz] *.0 [Hz] The lowest line is displayed when the SET key is pressed. Display when numeric entry is selected. Press the SET key, the numeric entry key is automatically established. Change data with the numeric entry key. Flicker 7 * FUNCTION SET * (00)Ref(Set).F [Hz] (2) After changing data Change data, then press the SET key. * FUNCTION SET * (00)Ref (Set).F [Hz} The lowest display disappears, and new data appears. Set data code list (Items selectable in function mode) Code Numbe 00 01 02 03 04 Display on LCD Descriptions Set ranges (Selection items) Fmax (Note 1) 280500 140250 80110 Linear SqrLaw Bend start Free start Decel stop Free stop Option Standard factory set data Setting resolution Units Rewriting in operation O O O O O Fmax means the maximum of Ref(Set).F, and other set values whose upper limit is Remarks Ref(Set).F Set frequency Forward jogging frequency Reverse jogging frequency Preset frequency 1 Preset frequency 2 Hz Hz Hz Hz Hz 05 Max. frequency Power control (base) frequency Rated output voltage Acceleration time (1) Deceleration time (2) Torque boost volume Setting overload ratio V/F pattern selection Start mode selection Stop mode selection Expanded set item selection Hz X 06 07 08 09 10 11 12 Rated Min F 400 200 100 1 1 1 Hz V V sec sec % Hz % X O O X X O O O Linear: V/F linear SqrLaw: V/F square reduction Bend: V/F folded line start: Starting at minimum frequency Free start: Free starting Decel stop: Stopping after deceleration Free stop: Free stopping For selecting items 17 and after. See the application manual. Depends on the 400V and 200V classes 13 V/F Pattern Linear X 14 start Decel stop X 15 X 16 O Note 1: When changing the set data of code number 05 (maximum frequency), also change the overfrequency in the following procedures: Select code number 16 Expanded set item selection to select. . Display code number 21 . Change data to a value higher than the setting of code 05 with the SET and numeric key entry. Data recording (1)When data of each function has been set, it should be protected as shown in below. (2)We remend that function data be stored separately, before maintenance work, in order to prevent the data from being lost due to unexpected accidents. 8 Operation Mode Display changes if the operation key is pressed. * OPERATION * REM/STOP/FOR/JOG () FOUT [Hz] REM: Remote operation is selected. DIR: Operation from the console is selected. FOR/REV:Forward/reverse selection. JOG: Jogging START/STOP: Starting or stopping operation. Monitor code number, content and data. to protect Data On pletion of adjustment, protect data in order to prevent it from being written or lost by maloperation, etc.. (1)Remove the cover from the unit. Open the console to the right. VFC61 SW1 ON 4 3 2 1 Set switch 4 of SW1 on the control PCB (VFC61) to ON. Any data cannot be written in the function mode. (2) Undo the console. Close the cover. Safety precaution Be sure to protect data while the VFC61 is stopped. 3. Automatic Measuring The exact constants (resistances) of the motor used with inverter should be set in order to run the inverter properly. Carry out automatic measuring for the motor only by disconnecting the motor from the load. Safety precaution As the voltage is impressed to the motor by automatic measuring, connect the GND terminal of the motor to ground. 9 (1) (2) (3) Inputting Motor Data Press the FUNC key. Select code number 16. Press the SET key, select SP, set2 with the up or down arrow keys, and press the SET key again. Change the code number displayed on the console one by one with the up or down arrow key. Set the data shown on the right according to the rating indicated on the name plate of the。