桥梁设计外文翻译资料内容摘要:
eveloped by NRS. The cycle for construction of each 5m wide bridge segment is a week, and two mobile units are being used on the Sundoya Bridge. These particular units were built for AS Anlegg to use on the Varodden Bridge in Kristiansand in Norway, and they have also been used by the same contractor on the Rafsundet Bridge. The design of the central part of the main span of the bridge is based on the use of lightweight concrete LC60 while other parts of the structure use the more standard type C65. Because of the aggressive marine environment, the quality of the concrete must be particularly good. The structure is a single cell, prestressed rectangular box girder, largely built using the travelling formwork system from NRS. The box width is 7m and its depth varies from 3m at the centre of the span to over the piers. Close to the abutments, concrete of quality C25 will be used inside the box girder as ballast. In addition, the designers have included the necessary elements inside the box girder in order to allow the possible addition of posttensioning cables in the future. The longterm behaviour of such large spans is not fully known, so the possibility that the main span may sag over time has to be taken into account. The width of the road is a constant from the barrier on one side to that on the other, and the total width of the bridge is some . There is a 2m wide footway included in the width of the structure. The pier shaft is formed with twin legs, which are hollow inside. The pier shafts incorporate permanent prestressing cables and they have a constant wall thickness and a width that varies parabolically over their height. Temporary tiedown piers are used to construct the bridge they are located 35m into each 120mlong side span from the main piers. Each consists of an Ishaped shaft, which is tied down to the ground using rock anchors and connected to the box girder by means of prestressing cables. The purpose of these structural elements is to support the cantilever and prevent rotation in strong winds. Once the brid。桥梁设计外文翻译资料
相关推荐
对主要材料预应力管桩的合格证和化验结果进行查验, 对不合格产品拒绝进场,严禁使用。 及时处理质量问题和质量事故。 及时向业主报告质量动态、质量趋势,每月向业主交一份监理月报。 预应力管桩施工控措施 ( 1)桩位、桩身垂直控制 ①要求场地表面平整而且有一定强度,保证施工中不造成陷机现象; ②桩位轴线施工队定好位后先自检,后通知监理单位进行复检,确保桩位 轴线按图定位; ③要求施工
der liquid essence(紫色液体)。 把 lemongrass 放入锅中加热,用勺子捞出放入玻璃杯。 把bitter aloe 捣成粉末放入,再把 juniper berries 捣成粉末后加热放入。 1药配好后得到 一个奇怪的标志 strange symbol。 1返回有很多门的房间,用 strange symbol 在右下角的地板上点一下,露出一个楼梯,下去。 铸造处
尽量大, BER 尽量小。 这样就可以有锁定频率,进行扫描了。 其中 LOCK 不用说是锁定的意思, SYNC 是同步的意思。 代表目前信号强度及信噪比足够,对钩表示已经锁定并且同步。 如果没有对钩,表示场强及信噪比还不够,无法锁定和同步。 还需要你再细调天线。 下面的卫星中是你正在查看场强的卫星。 转发器是改卫星下的转发器参数。 你需要做的是第一步在同一个卫星下
件的损伤是不可避免的,而且需耗费大量的钢筋水泥等原材料,且占用空间面积大,施工进展慢,需大量的人力及物力。 该方法是通过隔震产品将地震变形集中到隔震产品上,从而达到减少结构地震反应的目的,限制能量向上部结构传递,提高建筑物抗震的安全度。 隔震方法在美国、日本、台湾已有成功工程实例,如美国盐湖城大厦、洛杉矶政府大楼及 13本的办公楼、机场等均采用该方法,隔震效果十分明显。
每列均装有制动装置,操作方便、可靠。 当人进入相邻二架体时,可用制动装置锁定二架体,以防止架体意外移动而挤伤人。 边列有锁定装具,用于锁定整密集架,便于 档案 的保密。 中列制动装置 防护 装置 防震 ,防尘装置 20MM 磁性冰箱门吸条 每列的接触面均有缓冲及密封装置 ,具有良好的防震 ,防尘 ,防鼠 ,防光 ,防潮 ,防火功能 顶板 国内优质 冷轧钢板 GB/T7102020 防尘板、防鼠板