计算机专业外文翻译--中央处理器设计(编辑修改稿)

计算机专业外文翻译--中央处理器设计(编辑修改稿)内容摘要：

lthough we reuse and modify ponent designs from others , background information from these chapters is not repeated here. References, however, are given to earlier sections of the book, where detailed information can be found. The two CPUs presented are for a CISC using a nonpipelined datapath with a microprogrammed control unit and a RICS using a pipelined datapath with a hardwired pipelined control unit. These represent two quite distinct binations of instruction set architecture, datapath, and control unit. The plex instruction set puter The first design we present is for a plex instruction set puter with a nonpipelined datapath and microprogrammed control unit. We begin by describing the instruction set architecture, including the CPU register set, instruction formats, and addressing modes. The CISC nature of the instruction set architecture is demonstrated by its memorytomemory access for data manipulation instructions, eight addressing modes, two instruction format lengths, and instructions that require significant sequences of operations for their execution. We design a datapath for implementing the CISC architecture. The datapath is based on the one initially described in Section 79 and incorporated into a CPU in section 810. modifications are made to the register file, the function unit, and the buses to support the present instruction set architecture. Once the datapath has been specified, a control unit is designed to plete the implementation of the instruction set architecture. The design of the control unit must involve a coordinated definition of both the hardware organization and the microprogram organization. In particular , dividing the microprogram into microroutines, while at the same time designing the sequencer with which they interact, is a key part of the design. Even the instruction fields and opcodes are tied to this coordinated effort. Following the definition of the hardware and microcode organizations, we detail essential parts of the microcode and the microroutines for representative operations. 13 Instruction set architecture Figure 101 shows the CISC register set accessible to the programmer. All registers have 16 bits. The register file has eight registers, R0 though is a special register that always supplies the value zero when it is used as a source and discards the result when it is used as a destination. In additional to the register file, there is a program counter PC and stack pointer SP. The presence of a stack pointer indicates that a memory stack is a part of the architecture . the final register is the processor status register PSR, which contains information only in its rightmost the five bits。 the remainder of the register is assumed to contain zero. The PSR contains the four stored status bit values Z,N,C,and V in positions 3 through 0, respectively. In additional, a stored interrupt enable bit EI appears in position 4. Table 101 contains the 42 operations performed by the instructions. Each operation has a mnemonic and a carefully selected opcode. The operations are divided into four groups based on the number of explicit operands and whether the operation is branch. In addition, the status bits affected by the operation are listed. Figure 102 gives the instruction formats for the CPU. The generic instruction format has five fields. The first, OPCODE, specifies of the operation. The next two, MODE and S , are used to determine the addresses of the operands. The last two fields, SRC and DST, are the 3bit source register and destination register address fields, respectively. In addition, there is an optional second word W that appears with some instructions as an operand or an address, but not with others. The first two bits of OPCODE, IR(15:14), determine the number of explicit operands and how the fields of the format are used. When these bits are 00,either no operand is required or the location of the operand is implied by OPCODE. Only the OPCODE field is needed, as 14 shown in figure 2(b).the four rightmost OPCODE bits can specify up to 16 operands or with implied operand addresses. If IR(15:14) is 01, the instruction has one operand and is a data transfer or data manipulation instruction. Since there is an operand, the MODE field specifies the addressing mode for obtaining it. The single address may involve the DST register address in its formation, so the DST field is also present. The S field and SRC field relate to the presence of two operands and so are not used for the typical single operand instructions. but, the shift instructions require a shift amount to indicate how many bits to shift. For maximum flexibility, this shift amount is treated just like a source operand. As a consequence, the SHA and S fields is a full 16bit operand, but only values 0 through 15 are meaningful. There are sufficient OPCODE bits for 16 instructions with a single operand. Table 102 gives the addressing modes specified by the MODE field. The first two bits of MODE specify four different types of addressing: register, immediate, indexed, and relative to the PC. The third bit of MODE specifies whether the address generated by these modes is used as an indirect address. The one exception to this is direct addressing, which is obtained by applying indirection to the immediate type. Otherwise, if the third bit equals 0, indirect addressing does not apply whereas, if it equals 1, indirect addressing does apply. For the register type of instruction, MONE(2:1)=00 and the W word is not needed. Since the operand or address es from a register. The third column of the table provides register transfer statements for each of the addressing modes for the oneoperand instructions. If IR(15:14) is equal to 10, then the instruction has two addresses used for true operands. All fields of the g。